Design Of Kangaroo Shoes

Design of kangaroo shoes

The tongue of the kangaroo shoe is connected with the shoes and ears, forming a closed structure. It can effectively prevent sand from intruding into the shoes, and is often used in the design of military shoes, labor shoes, desert shoes and warm shoes.

The color picture K-9 is a male kangaroo working shoe, underneath the profile design.

1. finished product drawing

The process of turning color images into line tracing is the process of absorbing and absorbing the structure of kangaroo shoes.

Kangaroo structure relies on outer ear shoes.

As shown in figure 2-4-12.

The shoes have sharp ears and two eyes.

The shoe cover is connected with the shoe tongue, and the processing amount is wrapped around the shoe and the edge of the shoe.

The Mark machine is used to sew three rows of ridge, without the design of the stitched holes, only to adjust the size of the needle of the Mark machine.

The shoe is made of soft mouth and wrapped with foam cotton, so the height of the back can be raised properly, and the rear package is similar to the back cover of the sports shoes, and the upper part takes the Shuangfeng structure.

The shoe wrap and shoe ears are disconnected, and there are logo on the side.

2. structure design drawing

As shown in figure 2-4-13, first, according to the design rule of the outer ear shoes, the position of the shoe ears is designed, and the whole tongue cover and the enclosure parts are designed by using the replica board, and the difference between the inside and outside arms is determined, and the 01 and 02 points of the matching shoes and the location of the lock line are determined.

Then design the shoe day, the back pack, the break bar and the 1090.

Finally, make the difference between the bottom stretch and the inside and outside.

The difference between kangaroo shoe and ordinary shoe is that the tongue is closed, and the closed tongue is designed.

The specific steps are as follows:

(1) the 010'line outside the shoe tongue is a symmetrical middle line, and the contour lines of the shoe ears and the shoe tongue are reproduced in reverse, and the shoe eye positions are marked.

(2) connect the shoe line to the 02 point.

(3) trim the back end contour of the shoe tongue and turn the sharp corners into circular arcs.

3. preparation of basic templates for enclosure, shoe ears and shoe covers.

As shown in figure 2-4-14, the connection between the round bar and the shoe cover is the relationship between the shoe cover and the wrap around the fence. In the basic template, the connecting position, the locking position and the shoe eye position should be marked.

Among them, the shoes cover plus lOmm as the package quantity, draw the position of the connection on the fence, leave 5mm in the section of the shoe ears, then gradually pition to the section of the fence to leave lOmm.

This means that Mark machine is used to sew the ridge. First, the shoe cover is connected to the fence strip according to the mark of 5 ~ lOmm, then the folding and folding of the shoe cover is folded, and the machine is stitched by Mark machine.

The height of the seam bank is about 5mm.

Because the width of the girth is sewn into the lOmm, the area of the upper shoe will be reduced, and the area of the loss should be replaced by the corresponding area at the bottom.

The area of the ear shoes is not needed.

On the shoe cover, mark the machining position, lock position, shoe eye position, and add the amount of lOmm package.

4. the basic template for making heel and shoe.

The design of the rear heel is 10 to 15mm higher than that of the q-point, similar to the rear side of the sports shoes, and the upper part takes the arc shape, which is called the Shuangfeng structure.

Because of the use of flip stitching technology in the shoe, the amount of 3mm is kept.

Note that on the structural drawing, the 2 3mm to the top and the outer part of the upper part increase the thickness of the foam, as shown in figure 2-4-15.

The shoe bar has the difference between the inside and outside, leaving the amount of stubble and the amount of sewing.

Kangaroo shoes are a style change of sewing shoes.

When the machine is used to sew the ridge, the effect of controlling the seam is controlled by adjusting the stitching quantity and the distance between the stitches. When manual sewing is used, the holes should be punched and then sewed, and the stitching effect can be controlled by the distance and distance between the holes.